Construction Ventilation Fan 450 mm 592 W 8792 m³/h with 10 m Duct Hose 2 Speeds IP44, Vevor

Key Facts — Vevor BT-SHT16A Construction Fan 450 mm

• Brand: Vevor
• Model: BT-SHT16A-U(D)10 / SSG550W1016INSF6XV2
• EAN: 840349962641
• Type: Portable construction fan with duct hose, extract and supply
• Diameter: 450 mm
• Airflow: 5,175 CFM (8,792 m³/h)
• Power: 592 W, 220 V

The Vevor BT-SHT16A is a 450 mm construction fan moving 8,792 m³ of air an hour through a 10 metre duct hose. It draws dust, smoke, odours and hot air out of large spaces and discharges them through a window, door or gate — or reverses to pump fresh air in where work is under way.

The 592 W AC motor runs at 2,850 rpm with two speed settings, so airflow can be reduced when full capacity is not needed. The housing is steel with an anti-corrosion coating and the fan is ETL certified. The enclosure is rated IP44 and the motor has overheat protection for long sessions in damp conditions.

The fan measures 463 x 458 x 538 mm and weighs 30.4 kg. It has a carry handle and non-slip rubber feet, and the mains lead is 1.8 m with an earthed three-pin plug.

When does the Vevor 450 mm construction fan make the most sense?

When the volume is too large for a smaller portable fan. With 8,792 m³/h and 10 metres of duct, it can ventilate entire floors during demolition and sanding, large basements and warehouses, or carry fumes and dust out of a hall through a gate further away. Two speeds let the same fan run lower during drying-out and at full output during dusty tasks.

Applications for the construction fan

The construction fan is used during demolition, sanding and concrete work to remove dust, for damp remediation and drying of basements and crawl spaces, in warehouses and factories to extract hot air, in shafts and manholes to secure fresh air, and during painting and renovation to clear paint odour and sanding residue from the building.

Technical Specifications

Chosen by: Building contractors, demolition firms, damp remediation specialists, painters and caretakers of large premises.

Found in: Building sites, demolition and renovation, warehouses and factories, basements and shafts.

Frequently Asked Questions (FAQ)

Can one person carry the Vevor 450 mm construction fan?

For short distances, but it is heavy. The fan weighs 30.4 kg and measures 463 x 458 x 538 mm, so on stairs and when lifting onto scaffolding or a truck bed two people should share the load. On level ground it moves by the carry handle. The IP44 enclosure withstands splashes and damp but not hosing, so the fan must not stand in water when drying out flooded spaces.

Can a standard socket run the 592 W Vevor construction fan?

Yes. 592 W at 220 V is just under 3 A, which a standard earthed socket on a 10 A fuse handles comfortably, even with other equipment connected. The mains lead is only 1.8 m, so on site an extension cable is often needed — choose a heavy-duty, earthed cable rated for outdoor use. The fan has two speeds, and the lower setting is often enough for drying out.

What separates the Vevor 450 mm construction fan from a smaller portable ventilation fan?

Capacity and reach. A 200 mm portable fan moves around 1,700 m³/h through a 5 m hose, while the Vevor BT-SHT16A moves 8,792 m³/h through 10 m of duct — enough for entire floors and halls rather than single rooms. The cost is size and weight: 30.4 kg against just over 10 kg, making it less suited to quick moves between rooms.